Pressure Compensating Emitters
Part NumberDescription
MF-1/2Acu-emitter, pressure compensating, self-flushing, .187 barb  inlet x 1/8" outlet barb, .50 GPH Red
MF-3/4Acu-emitter, pressure compensation, self-flushing, .187 barb inlet x 1/8" outlet barb, .75 GPH Gray
MF-1Acu-emitter, pressure compensating, self-flushing, .187 barb inlet x 1/8" outlet barb, 1 GPH Black
MF-2Acu-emitter, pressure compensating, self-flushing, .187 barb inlet x 1/8" outlet barb, 2 GPH Green





Wade Rain Acu-Emitters are self-purging pressure compensating emitters which mount "on-line" to a polyethylene lateral. Automatic flushing at start-up and shut-down occurs at approximately 1 psi. A double-sided silicone diaphragn allows purging and delivers a constant discharge rate through a range of 10-60 psi. These emitters can be fitted with small diameter porting tubing to deliver water to a location away from the emitter. Maximum Recommended Working Pressure - 60 PSI. All Acu-emitters use .125" I.D. porting tubing.

6 & 12-WAY PRESSURE COMPENSATING EMITTERS
Part NumberDescription
MF6-1/26-way Acu-emitter with .187 barb inlet x 1/8" outlet, self-flushing, .5 GPH per outlet, Red base
MF6-16-way Acu-emitter with .187 barb inlet x 1/8" outlet, self-flushing, 1 GPH per outlet, Black base
MF6-26-way emitter with .187 barb inlet x 1/8" outlet, self-flushing, 2 GPH per outlet, Green base
MF12-1/212-way Acu-emitter with .187 barb inlet x 1/8" outlet, self-flushing, .5 GPH per outlet, Red base
MF12-112-way Acu-emitter with .187 barb inlet x 1/8" outlet, self-flushing, 1 GPH per outlet, Black base

MF12-2


2 Multi-port emitter with .187 barb inlet x 1/8" outlet, self-flushing, 2 GPH per outlet, Green base










Wade Rain 6-Way and 12-Way Acu-Emitters- Silicone diaphragm each outlet. One outlet only (per side) open. Snip open others as needed. Be sure "snipped" outlets ar fully open to prevent flow restriction. Flow rate shown on housing. Maximum Recommended Working Pressure - 60 PSI. All Acu-emitters use .125" I.D. porting tubing.

Wade Rain Emitters

Turbulent Flow Emitters
Part NumberDescription
CO1/2Clip-on emitter, 1/4" barb inlet, .5 GPH - Red
CO1Clip-on emitter, 1/4" barb inlet, 1 GPH - Blue
CO2Clip-on emitter, 1/4" barb inlet, 2 GPH - Green

Screw On Emitter
SO1/2Screw-on emitter, screws into 125-185 tubing, .5 GPH- Red
SO1Screw-on emitter, screws into 125-185 tubing, 1 GPH- Blue
SO2Screw-on emitter, screws into 125-185 tubing, 2 GPH- Green









Wade Rain Turbulent Emitters utilize the turbulent-flow labyrinth method of energy dissipation to achieve prediction flow rates. This design includes relatively large flow paths which minimize clogging. Maximum Recommended Working Pressure - 40 PSI

Acu-Emitter Punch Tools

Part NumberDescription
PQP125Quick Punch- punches hole for 1/8" & 1/4" barb fittings. Handle inserts 1/4" connectors
RPHand held punch prepares hole in polyethylene tubing for mounting of emitters, fittings, etc.
MFITBlack in color. Used to greatly assist in inserting the Acu-Emitter into polyethylene tubing












Mid-Atlantic Irrigation Co., INC​